2015年3月20日金曜日

ビートマッチング Beat Matching

今日はビートマッチングについてです。TrAとTrBでビートマッチングをさせる場合、操作は大きく分けると2つになります。「BPM合わせ」と「ビート位置合わせ」です。GODJは各音楽ファイルのBPMを自動で計算してくれますので、その結果が正しければBPM合わせは簡単、TrAとTrBのBPM値①を画面横にあるテンポスライダー②で調整するだけです。



「ビート位置合わせ」はピッチベンドを使います。音楽再生中にアークセレクタをCUE CLEARの位置に移動させるとターンテーブルが下図のようなピッチベンドコントローラになります。



この状態でターンテーブル上部の紫色の部分をタッチするとその曲のスピードがわずかに下がり、下部の青色の部分をタッチするとわずかに上がります。操作しているトラックのビート位置が反対側のトラックに対して早いと感じた場合は上を、遅いと感じた場合は下をタッチしてビート位置を微調整します。この変化量はオプションメニューにて1%~16%の範囲で設定する事ができます。またPITCH LOCKを有効にしておくとピッチベンド中も音程が一定に保たれます。

ピッチベンドコントローラの左右のグレーの部分、ここをタッチすると再生位置が1ビート分前後に飛びます。この機能によりビートは合っているけど拍が合っていないという状態を修正する事ができます。

(例)
TrA: 1234 1234
TrB: 2341 2341
となっている場合、TrBのピッチベンドコントローラの左をタッチするとTrBの再生位置がが1ビート戻り
TrA: 1234 1234
TrB: 1234 1234
となります。

Today in this post I'd like to talk about beatmatching. Operations for beat matching are classified into two groups: BPM adjustment and beat position adjustment. Since GODJ automatically analyzes the BPM for each music file, BPM adjustment is very easy as long as the results are correct. All you have to do is to adjust the BPM value (1) to the same value of the other track using tempo slider (2).


You can perform beat position adjustment using a pitch bend function. While playing a music file, the turntable changes its surface to pitch bend controller shown below when you place the arc selector at CUE CLEAR position.

In this mode, when you touch the top purple area, the speed goes down a little, when you touch the bottom blue area, the speed goes up a little. If you feel the beat position of the track being controlled is faster than the opposite track, touch the top area, and if you feel it is slower, touch the bottom area to adjust beat position. In the option menu, you can change the pitch bend depth between 1% and 16%. Pitch lock is applied to pitch bend too if you set the pitch lock switch on.  

You can skip the playing position back or forth for 1 beat by touching the gray area at left and right side of the pitch bend controller. Using this function you can correct situations where the beat is matched but the beat count is not aligned.

(For Example)
TrA: 1234 1234
TrB: 2341 2341
In this situation, when you touch the left area of the pitch bend controller of the TrB. 

The playing position of the TrB goes back for 1 beat. Then it will adjust to:
TrA: 1234 1234
TrB: 1234 1234

Advanced Tip:  You may also adjust the BPM by placing on finger on the Tempo Slider and turning the Function knob respective to the appropriate track side. (TrA / TrB)

0 件のコメント:

コメントを投稿